tii


 

DSL


Tii's broad family of DSL products enhances the delivery of high speed data, phone and IPTV services over conventional copper wire. Each product is designed to filter or split DSL (data) and POTS (Plain Old Telephone Service) signals. This splitting of filtering may take place in either the Network Interface Device (NID) or inside the customer premise.

BIX-5UVS-12 - 5 Pair xDSL POTS Splitter with 25 Pair BIX Distribution Connector

The BIX-5UVS-12 is a 5 pair xDSL POTS splitter for multi-pair xDSL service deployments utilizing BIX mounting rack system. The module incorporates five independent UVS-12 DSL splitter circuits. Each splitter circuit is designed to be installed in series on the telephone line at the customer premise, providing a filtered POTS line connection for customer use. The BIX-5UVS-12 xDSL POTS Splitter is designed to be used for all DSL services operating up to 30 MHz frequencies.

AdobePDF.jpg read more (PDF)

372S-12LP - xDSL POTS Splitter Module for VDSL2/ADSL2+, IPTV Services

The 372S-12LP xDSL POTS Splitter Module splits the combined voice and data signals carried on telephone lines providing separate outputs for both phone and data services. The 372S-12LPB utilizes enhanced circuit components to meet VDSL2/ADSL2+ splitter specifications for advanced data and IPTV deployments.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

80-800 - Indoor VDSL2 Balun

The 80-800 Indoor VDSL2 Balun is a passive in-line device designed to convert a VDSL2 signal carried on unbalanced 75 Ohm coax cable to a balanced twisted pair signal.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

103-105-3C1ES-N, 103-105-3C1FS-N - Solid State 240V and 300V Protector Modules

Tii's line of xDSL Solid State Protector Modules provides dependable protection for today's high speed communications networks. Balanced, ultralow capacitance, solid state circuitry minimizes noise and signal loss in high frequency networks. The modules protect sensitive circuitry by responding to surges in nanoseconds. Breakdown voltage is tightly controlled by clamping precisely and dependably even after long repeated use. An integral fail-safe mechanism permanently shorts the protector to ground in the presence of sustained overvoltage.

AdobePDF.jpg read more (PDF)

761SM-12 - Surface Mount Wall Jack with xDSL Filter

The 761SM-12 Wall Mount DSL Filter splits the combined voice and data signals carried on telephone lines providing separate outputs for both phone and data services. The 761SM-12 utilizes Tii's proprietary gel filled IDC rockers for wire terminations. The IDC rockers are color coded for tip and ring wire orientations. Termination of wires is easy as the wires do not need stripping. All one needs is to lift the rocker, straighten ends of the wire, insert and pull the rockers in fully down position.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

69M Series - Sealed Wire Terminal

The 69M Series Sealed Wire Terminal is designed for applications requiring more than one parallel connection (extension) to a single or two pair service. This product is an ideal fit for Voice Over Internet Protocol (VoIP) networks.

AdobePDF.jpg read more (PDF)

68M-2S - Sealed Wire Terminal with Home Security Connections

The 68M-2S is designed for applications requiring more than one parallel connection to a single service in addition to providing connectivity to an existing Home Security System. This product is an ideal fit for digital voice networks connected to a home security system.

AdobePDF.jpg read more (PDF)

68M-2-1T - Two Line Sealed Wire Terminal with RJ-11 Tail/Connector

The 68M-2-1T Sealed Wire Terminal is designed for applications requiring more than one parallel connection (extension) to a single or two pair service.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

68M-12-1T - Twelve-Line Sealed Wire Terminal with RJ-21 Tail/Connector

The 68M-12-1T Sealed Wire Terminal is designed for applications requiring an amphenol to twisted pair copper IDC termination.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

68M-1-1T - Single Line Sealed WIre Terminal with RJ-11 Tail/Connector

The 68M-1-1T Sealed Wire Terminal is designed for applications requiring more than one parallel connection (extension) to a single or two pair service.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

68M Series - Sealed Wire Terminal

The 68M Series Sealed Wire Terminal is designed for applications requiring more than one parallel connection (extension) to single or two pair service.

AdobePDF.jpg read more (PDF)

170 Series - Outdoor Sealed Wire Terminal Enclosure

170 Series Outdoor Sealed Wire Terminal Enclosures are versatile outdoor housings, designed and tested to the industry's most stringent environmental standards. The 170 is specifically designed to accommodate two separate 68 Series or SVM Series modules in the upper or lower positions of the enclosure. Featuring snap-in retaining tabs, this flexible design offers the customer the ability to order the 170 in multiple configurations.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

168 Series - Outdoor Sealed Wire Terminal Enclosure

The 168 Series Outdoor Sealed Wire Terminal Enclosure accommodates the Tii 68 Series Sealed Wire Terminal. The 68 Series is designed for applications requiring more than one parallel connection to a single or two pair service. This product is an ideal fit for digital voice networks.

AdobePDF.jpg read more (PDF)

751B - Surface Mount Gel-Sealed Telephone Jack

The 751B is a single line, indoor gel-sealed unit ideally suited for indoor telephone connections or demarcation applications. This unit is compact and may be mounted to any suitable flat surface.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

WTB-025-C04 - 25 Line Sealed Wire Terminal with 4FT CAT3 Cable Stub

The WTB-025-C04 Sealed Wire Terminal is designed for applications requiring 25 pair output with 24awg cable.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

68M-12-C04 - Twelve Line Sealed Wire Terminal with 4ft. Cat3 Cable Stub

The 68M-12-C04 Sealed Wire Terminal is designed for applications requiring 12 pair output with 24awg cable.

AdobePDF.jpg read more (PDF)

3310D Series - DSL POTS Splitter Outdoor Ancillary Devices

The 3310D DSL POTS Splitter Outdoor Ancillary Device splits the combined voice and data signal carried on telephone lines to provide separate outputs for both phone and data services. Asymmetrical Digital Subscriber Line (ADSL) provides high-bit-rate digital information over telephone subscriber lines. "POTS" stands for Plain Old Telephone Line. The 3310D-12 splitter ancillary device is for IPTV services and utilizes enhanced circuit components to meet VDSL/ADSL2+ requirements.

AdobePDF.jpg read more (PDF)

ISB - Intercom System Bypass

The ISB enables sensitive VDSL2 signals to bypass around telephone and gate entry systems commonly used in apartment buildings and gated communities. The module enables the POTS portion of the Telco's signals to be routed through the entry system and recombined with the pristine DSL signal for transport to the apartment or home, avoiding the severe losses associated with routing the DSL signal through the telephone entry system. The ISB module easily snaps into the ISB PLATE adapter panel.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg ISB MODULE Installation Notes (PDF)
AdobePDF.jpg ISB PLATE Installation Notes (PDF)

97FB-S - VDSL POTS Splitter Module with VDSL Output on Coax Port

The 97FB-S VDSL POTS Splitter Module splits the combined voice and data signal carried on telephone lines. The POTS output is provided on a dual IDC connector, and VDSL output on a 75 Ohm female "F" coax connector. The balanced twisted pair input signal is impedance matched to a single ended coax VDSL output which is lowpass filtered to 8.5MHz, allowing for coexistence with 12-28MHz HPNA signals on a single coax wire. The 97FB-S module also provides the Tii Auto-Jack, a switchable RJ-11 jack, as the customer demarcation point.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

372S-12 - xDSL POTS Splitter Module for VDSL2/ADSL2+, IPTV Services

The 372S-12 xDSL POTS Splitter Module splits the combined voice and data signals carried on telephone lines providing separate outputs for both phone and data services and utilizes enhanced circuit components to meet VDSL2/ADSL2+ splitter specifications for advanced data and IPTV deployments.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

80-100 - Indoor DSL Filter

The 80-100 Indoor ADSL low pass filter is a passive in-line device designed to block Asymmetric Digital Subscriber Line (ADSL) signals from the subscriber's telephone line, allowing the POTS signal to pass through unaffected.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

80-200 - Indoor DSL Filter With Data Port

The 80-200 Indoor ADSL low pass filter is a passive in-line device designed to block Asymmetric Digital Subscriber Line (ADSL) signals from the subscriber's telephone line, allowing the POTS signal to pass through unaffected. The unit is designed with a second unfiltered RJ-11 jack on the output side for connection to DSL equipment.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

80-400 - Indoor DSL Filter with Data Port

The 80-400 Indoor ADSL low pass filter is a passive in-line device designed to block Asymmetric Digital Subscriber Line (ADSL) signals from the subscriber's telephone line, allowing the POTS signal to pass through unaffected. The unit is designed with a second unfiltered RJ-11 jack on the output side for connection to DSL equipment.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

80-410V - Indoor DSL POTS Splitter Module for VDSL2/ADSL2+, IPTV Services

The 80-410V Indoor DSL POTS Splitter Module splits the combined voice and data signals carried on telephone lines providing separate outputs for both phone and data services. It is designed to be mounted inside the customer premises near where the phone service enters the building. RJ jacks or sealed rocker/IDC terminals connect directly to the equipment with data-grade cabling. Utilizes enhanced circuit components to meet VDSL2/ADSL2+ splitter specifications for advanced data and IPTV deployments.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

80-500 - Indoor In-Line xDSL Filter

The 80-500 Indoor In-Line xDSL low pass filter is a passive in-line device designed to block Asymmetric Digital Subscriber Line (xDSL) signals from the subscriber's telephone line, allowing the POTS signal to pass through unaffected. The unit is designed with a second unfiltered RJ-11 jack on the output side for connection to DSL equipment.

AdobePDF.jpg read more (PDF)

SCT-A - Active Sealing Current Terminator

The Active Sealing Current Terminator is a microprocessor controlled circuit that provides DC sealing current terminations to non telephone service DSL subscriber lines. It maintains network connection integrity by allowing current to flow through "DSL Only" service.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

87-1 - Sealed Customer Bridge Module with POTS Suppression

The 87-1 Sealed Customer Bridge Module (CBM) with POTS Suppression is designed to allow DSL service to pass through the unit while blocking traditional voice telephone service signals.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

95S-1-09 - ADSL2+ POTS Splitter Module

The 95S-1-09 ADSL2+ POTS Splitter Module splits the combined voice and data signal carried on telephone lines to provide separate outputs for both phone and data services.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

95S-1-10 - Sealed Customer Bridge Module Equipped with DSL Compliant Half-Ringer

The 95S Series eliminates DSL signal loss caused by traditional Customer Bridge Modules (CBM) incorporating half-ringer circuits. It also enables MLT half-ringer signature identification.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

95S-1-11 - DSL POTS Splitter Module

The 95S Series ADSL POTS Splitter Module splits the combined voice and data signals carried on telephone lines to provide separate outputs for phone and data services. The 95S-1-11 utilizes enhanced circuit components to meet ADSL2+ services for IPTV requirements.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

95S-1-12 - DSL POTS Splitter Module for VDSL2/ADSL2+, IPTV Services

95S-1-12 DSL POTS Splitter Module splits the combined voice and data signals carried on telephone lines providing separate outputs for both phone and data services. This module utilizes enhanced circuit components to meet VDSL2/ADSL2+ splitter specifications for advanced data and IPTV deployments.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

96 Series - xDSL POTS Splitter Module

The 96 Series xDSL POTS Splitter Module splits the combined voice and data signal carried on telephone lines to provide separate outputs for both phone and data services.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg 96-00 Installation Note (PDF)
AdobePDF.jpg 96-00-1 Installation Note (PDF)
AdobePDF.jpg 96-00-4 Installation Note (PDF)
AdobePDF.jpg 96-00-5 Installation Note (PDF)

97 Series - VDSL/ADSL2+ POTS Splitter Modules

97 Series VDSL/ADSL2+ POTS Splitter Module are passive devicse which split the combined voice and data signal carried on telephone lines to provide separate outputs for both phone and data services.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

97C-1-1-2 - ADSL2+ POTS Splitter Module

The 97C-1-1-2 ADSL2+ POTS Splitter Module is a passive device which splits the combined voice and data signal carried on telephone lines to provide separate outputs for both phone and data services.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

712 Series - MDU xDSL POTS Splitter Panel

The 712-99S-12 is equipped with 99S Series VDSL2/ADSL2+ POTS Splitter Modules that split the combined voice and data signal carried on telephone lines to provide separate outputs for both phone and data services. The 99S-12 utilizes enhanced circuit components to meet VDSL2/ADSL2+ service for IPTV requirements. The 712 Series Mounting Plate comes equipped with wire guides and retainers to facilitate up to 12 99S-12 modules.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

761-4T-12 - Flush Mount POTS Splitter for VDSL2/ADSL2+, IPTV Services

The 761-4T-12 Series POTS Splitter splits the combined voice and data signals carried on telephone lines providing separate outputs for both phone and data services. The 761-4T-12 utilizes enhanced circuit components to meet VDSL2/ADSL2+ splitter specifications for advanced data and IPTV deployments.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

UVS-12 - xDSL POTS Splitter

The UVS-12 POTS Splitter is a single line unit designed to be installed in series on the telephone line at the customer's premises providing a filtered POTS line connection for customer use. The UVS-12 xDSL POTS Splitter is designed to be used for all DSL services operating up to 30 MHz frequencies.

AdobePDF.jpg read more (PDF)
AdobePDF.jpg Installation Notes (PDF)

About Tii

About Us



Follow Us On:

Facebook   Twitter   YouTube
Email Newsletter icon, E-mail Newsletter icon, Email List icon, E-mail List icon

Join our FREE Email Mailing List

For Email Newsletters you can trust
© 2019 Tii Technologies Inc. All Rights Reserved